How tight should you actually tighten a stainless steel screw? This is one of the most common questions we receive. If you tighten it too little, the joint will be loose and may come undone. If you tighten it too much, the threads can seize or the screw may snap. Here you will find a clear torque table for stainless steel screws in A2 and A4, along with some tips to ensure the joint lasts for many years.
Watch video: Tightening torque for stainless steel screws
Start by reading the head
On stainless steel screws according to ISO 3506, the material and property class are stamped on the head, for example A2-70 or A4-80:
- A2 is stainless steel (AISI 304) and A4 is acid-proof steel (AISI 316) with molybdenum.
- The number after the hyphen indicates the tensile strength in tens of MPa: 70 = 700 MPa and 80 = 800 MPa.
- It is the property class, not A2 or A4, that determines the torque. An A2-70 and an A4-70 are therefore tightened with the same torque.
Tightening torque for stainless steel screws (Nm)
The table applies to coarse-threaded (metric) screws with lubricated or waxed threads.
| Thread | Pitch (mm) | Class 50 (Nm) | A2-70 / A4-70 (Nm) | A4-80 (Nm) |
|---|---|---|---|---|
| M3 | 0.5 | 0.41 | 0.87 | 1.2 |
| M4 | 0.7 | 1.0 | 2.0 | 2.7 |
| M5 | 0.8 | 1.9 | 4.1 | 5.4 |
| M6 | 1.0 | 3.3 | 7.0 | 9.3 |
| M8 | 1.25 | 7.8 | 17 | 22 |
| M10 | 1.5 | 15 | 33 | 44 |
| M12 | 1.75 | 27 | 57 | 76 |
| M14 | 2.0 | 43 | 91 | 121 |
| M16 | 2.0 | 65 | 140 | 187 |
| M20 | 2.5 | 127 | 273 | 364 |
| M24 | 3.0 | 220 | 472 | 629 |
The values are reference values from industry torque tables for stainless steel screws. Always follow the manufacturer's or designer's instructions if available. Dry or fine-threaded screws require different values.
Why is lubrication so important for stainless steel?
Stainless against stainless has high friction. Under pressure, the threads can seize (also known as galling), which causes the joint to lock up and the screw may break if you continue to tighten. With a little lubricant, the friction becomes even, and the same torque produces the correct preload every time.
- Use wax, molybdenum disulfide (MoS₂), or an anti-seize paste for stainless steel.
- Ensure the threads are clean from dirt and metal shavings before assembly.
- Read more in our post about thread seizing in screw joints.
How to tighten correctly
- Use a torque wrench. Set the value from the table and tighten until the wrench clicks.
- Tighten evenly and steadily. Fast, jerky movements and impact wrenches increase the risk of seizing.
- Tighten crosswise for multiple screws. For flanges and lids, tighten in two to three stages, crosswise, so that the pressure is even.
- Is there resistance? Stop. Loosen, check the threads, lubricate, and start over instead of forcing it.
Frequently asked questions
Are A2 and A4 tightened with the same torque?
Yes, if they have the same property class. A2-70 and A4-70 are tightened with the same torque. A4-80 can withstand approximately one-third more.
Can I use this torque table for standard steel screws (8.8)?
No. Zinc-plated steel screws in class 8.8 and higher have different strength values and friction coefficients and must be tightened according to their own table.
Does the table apply when the screw is tightened into a nut?
Yes, as long as the nut has at least the same property class as the screw, for example an A4-70 screw with an A4-70 nut, and the threads are lubricated.
Find the right screw
With us, you will find stainless hex bolts, socket head screws, nuts, and threaded rods in A2 and A4. If you have questions about which fastener suits your project, you are welcome to contact us.
